Pile Foundations

0
Foundation Engineering • Chapter 8

Pile Foundations: Exhaustive Master Study Guide & Solved Numericals

The definitive engineering reference covering theoretical derivations, complete classifications, static and dynamic capacity formulas, pile load testing, group load distribution, negative skin friction, construction methodologies, and all 25 university board examination problems solved step by step.

8.1 Introduction, Classification, and Uses

8.1.1 Detailed Introduction

  • A pile is a slender structural foundation member having a very small cross-sectional area relative to its length. Piles are manufactured from high-strength structural steel, reinforced or prestressed concrete, or treated timber.
  • Piles function as deep foundation elements that transmit heavy superstructure loads through weak, compressible upper soil strata down to deeper, stiffer, and less compressible bearing strata where the depth-to-width ratio satisfies Df > W (typically Df / B ≥ 4 to 5).
  • Pile foundations are indispensable when shallow foundations (isolated footings, combined footings, or raft foundations) cannot safely support structural loads without exceeding allowable bearing capacity or causing excessive differential settlement.

8.1.2 Comprehensive Classification of Pile Foundations

A. According to Construction Material Used
  • i) Steel Piles: Generally fabricated as thick-walled circular steel pipes or rolled steel H-sections. Steel piles are driven into the ground with either open or closed bottom ends (closed-end pipes are subsequently filled with structural concrete). They withstand hard driving stresses in dense soils and carry exceptionally heavy axial loads.
  • ii) Concrete Piles: Divided into two primary categories:
    • Precast Concrete Piles: Cast, cured, and prestressed or reinforced in a factory or casting yard, then transported and driven into place. They offer high quality control and resistance to chemical attack.
    • Cast-in-Situ Concrete Piles: Constructed directly at the project site by boring or driving a temporary casing into the ground and filling the excavated cavity with fresh concrete and reinforcement.
  • iii) Timber Piles: Prepared from straight, sound tree trunks (such as Sal, Teak, or Pine) after debarking and trimming. Timber piles must be straight, sound, and free from structural defects like knots and splits. They are treated with creosote preservatives when extending above the permanent groundwater table.
  • iv) Composite Piles: Formed by joining two different materials along the vertical shaft—commonly a lower section of treated timber or steel pipe (positioned permanently below the groundwater table to prevent rot) combined with an upper section of cast-in-situ concrete.
B. According to Function / Load Transfer Mechanism
  • i) End / Base / Point Bearing Piles: Transfer structural loads directly through the pile tip onto a firm bearing stratum (such as dense gravel or sound rock), passing completely through soft compressible soil layers or standing water.
  • ii) Friction Piles: Transfer loads primarily through skin friction and adhesion mobilized along the embedded surface of the pile shaft and surrounding soil when no hard bearing stratum exists at a practical drilling depth.
  • iii) Combined End Bearing and Friction Piles: Resist applied loads simultaneously through tip bearing resistance at the base and shaft friction along the embedded perimeter.
Soft material Soft material (i) End Bearing (ii) Friction (iii) Combined
Figure: Load transfer mechanisms in (i) End-bearing, (ii) Friction, and (iii) Combined piles.
C. According to Method of Installation
  • i) Driven Piles: Preformed piles (steel, timber, or precast concrete) forced into the ground by repeated impact blows of a heavy pile-driving hammer.
  • ii) Driven and Cast-in-Situ Piles: Formed by driving a steel casing with a closed bottom end (shoe or concrete plug) into the soil, filling the casing with concrete, and either leaving the shell in place or withdrawing it during concreting.
  • iii) Bored and Cast-in-Situ Piles: Constructed by excavating or drilling a borehole into the ground (with or without casing/bentonite slurry) and filling the cleaned hole with reinforcement and concrete.
  • iv) Screw Piles: Shafts fitted with wide helical blades at the base that are screwed into soft or cohesive soils using rotational torque.
  • v) Jacked Piles: Installed silently and without vibration by pressing pile segments into the soil using hydraulic jacks reacting against an existing structure or kentledge (ideal for underpinning).
D. According to Engineering Use
  • i) Load-Bearing Piles: Transfer vertical downward loads from buildings, bridges, and towers to suitable bearing strata by end bearing, friction, or both.
  • ii) Compaction Piles: Driven into loose granular soils solely to densify the surrounding soil mass and increase its relative density and bearing capacity (often sand piles).
  • iii) Tension (Uplift) Piles: Anchor structures subjected to upward hydrostatic buoyancy or overturning moments (such as dry docks, transmission towers, and tall chimneys).
  • iv) Sheet Piles: Interlocking thin sections (steel, timber, or concrete) driven edge-to-edge to form a continuous retaining wall, cofferdam, or cutoff bulkhead for earth and water retention.
  • v) Anchor Piles: Installed behind sheet pile bulkheads to provide horizontal tie-back anchorage against lateral earth pressures.
  • vi) Fender & Batter Piles: Batter (inclined) piles resist large horizontal/inclined forces, while fender piles protect marine docks and bridge piers from vessel impact.
E. According to Soil Displacement
  • i) Displacement Piles: All driven piles (closed-end pipes, precast concrete, timber) fall under this category; soil is displaced laterally and downward during driving, densifying loose sands and remolding clays.
  • ii) Non-Displacement Piles: All bored piles belong to this category because the in-situ soil is excavated and removed during boring without lateral soil displacement.

8.1.3 Uses of Pile Foundations

  1. Transfer heavy structural loads through soft upper strata to a stronger and/or less compressible deep bearing stratum.
  2. Support structures in deep deposits of weak soil through skin friction between the pile shaft and surrounding soil.
  3. Compact loose granular soils to increase relative density and reduce liquefaction potential.
  4. Resist uplift (tensile) forces acting on submerged basements, dry docks, and tall wind-loaded towers.
  5. Carry horizontal and inclined lateral forces from bridge abutments, retaining walls, and offshore structures.
  6. Provide foundation support safely below the maximum scour depth in riverbeds and coastal channels.
  7. Stiffen the soil beneath heavy machine foundations to control both vibration amplitudes and the natural frequency of the soil-foundation system.
  8. Serve as a practical alternative whenever shallow foundations cannot safely support the structure alone.

8.2 Selection of Pile Type

Selecting the most appropriate pile type requires careful evaluation of technical, environmental, and economic parameters:

  1. Required length of pile in relation to the applied structural load and subsurface soil stratification.
  2. Character, rigidity, and settlement tolerance of the superstructure.
  3. Local availability of construction materials (steel sections, aggregate, timber) and specialized piling rigs.
  4. Types and magnitudes of loading (axial compression, uplift tension, lateral thrust, or dynamic machine vibration).
  5. Subsurface factors causing material deterioration (groundwater acidity, sulfates, chlorides, stray currents, or marine borers).
  6. Ease of installation, quality control inspection, and long-term maintenance.
  7. Estimated total cost of each pile alternative taking into account initial construction cost and service life expectancy.
  8. Projected future cost of maintenance and rehabilitation.
  9. Overall project budget and availability of funds.

8.3 Load-Carrying Capacity of Single Piles

Exam Focus: [2016-Spring (PU): 4.(a)], [2017-Fall (PU): 4.(a)], [2018-Spring (PU): 6.(a)]

8.3.1 Static (Analytical) Method

The ultimate axial load capacity (Qu) of a single pile is the sum of its ultimate end-bearing resistance (Qb) and ultimate skin-friction resistance (Qs):

∴   Qu = Qb + Qs = qb · Ab + fs · As
  • For Cohesive Soils (Clays, ϕ = 0°):
    Qu = Cu · Nc · Ab + α · Cu · As
    Where Cu = undrained cohesion at the pile tip (usually Nc = 9 for deep foundations), Cu = average undrained cohesion along the shaft, α = adhesion factor (0.3 to 1.0), Ab = base area, and As = shaft surface area (π·d·L for circular piles; 4·b·L for square piles).
  • For Cohesionless Soils (Sands, c = 0):
    Qu = (σ'v(tip) · Nq) · Ab + (K · σ'v · tan δ) · As
    Where σ'v(tip) = effective vertical overburden pressure at the pile tip (limited to critical depth 15d–20d), Nq = bearing capacity factor, K = coefficient of lateral earth pressure, σ'v = average effective overburden pressure along the shaft, and δ = angle of wall friction between soil and pile (typically 0.75ϕ).

8.3.2 Dynamic Pile-Driving Formulas

Dynamic formulas estimate ultimate pile capacity in cohesionless sands by equating the kinetic energy delivered by the driving hammer to the work done in penetrating the soil:

1. Engineering News-Record (ENR) Formula
Qa = W · hFOS · (s + C) = W · h6 · (s + C)

Where W = weight of hammer, h = height of drop, s = final set (penetration per blow), FOS = 6, and constant C = 2.5 cm (for drop hammers) or C = 0.25 cm (for single/double-acting steam hammers).

2. Hiley’s Formula (More Rational Dynamic Formula)
Qu = W · h · ηh · ηbs + c2    and    Qa = QuFOS

Where ηh = hammer efficiency (0.75–0.85 for drop hammers), c = c1 + c2 + c3 = total temporary elastic compression of dolly/cap, pile, and soil, and ηb = efficiency of hammer blow:
• When W > e·P:   ηb = W + e2PW + P
• When W ≤ e·P:   ηb = W + e2PW + P − (W − e·PW + P)2
(Here P = weight of pile + helmet + dolly, and e = coefficient of restitution).

8.5 Pile Load Test (Direct Field Method)

Exam Focus: [2015-Fall (PU): 5.(b)], [2018-Spring (PU): 6.(a)]
  • Purpose: The static vertical pile load test is the most reliable field method for verifying the ultimate and safe working load-carrying capacity of a single pile and checking its load-settlement response.
  • Test Setup & Procedure: A hydraulic jack reacts against a heavily loaded kentledge platform or anchor-pile reaction girder to apply incremental vertical loads (typically in steps of 20% of the expected design load up to 2.0–2.5 times the working load). Dial gauges mounted on an independent reference beam record pile-head settlement at each load stage until the rate of settlement falls below 0.25 mm/hr.
  • Determination of Allowable Load (IS 2911 / Standard Criteria): The safe working load is taken as the least of:
    1. Two-thirds (2/3) of the final load at which total settlement reaches 12 mm.
    2. Fifty percent (50%) of the final load at which total settlement equals 10% of the pile diameter (or 7.5% for under-reamed piles).
    3. Ultimate failure load divided by a suitable Factor of Safety (FOS = 2.0 to 2.5).

8.6 Analysis of Pile Groups

8.6.1 Pile Group Subjected to Eccentric Vertical Load

  • For a symmetrical pile group capped by a rigid, thick pile cap subjected to a central vertical load (Qg) distributed across n piles, the vertical load carried by each individual pile is:
∴   Qi = Qgn
  • When the resultant vertical load Qg acts eccentrically at coordinates (ex, ey) relative to the centroid of the pile group, the load on any individual pile i is given by:
∴   Qi = Qgn ± MyΣx2 · x ± MxΣy2 · y
Y Y X X cg R(x, y) ey ex
Figure: Plan of a symmetrical pile group subjected to an eccentric vertical load R(x, y).
Where:
• Qi = Axial load transmitted to the i-th pile
• Qg = Total vertical load acting on the pile group
• n = Total number of piles in the group
• Mx = Moment about the x-axis = Qg × ey
• My = Moment about the y-axis = Qg × ex
• ex, ey = Eccentricities of the resultant load along the x and y directions
• Σx2, Σy2 = Sum of the squares of pile coordinates measured from the y-axis and x-axis, respectively
• Sign Convention: Clockwise moments (Mx, My) are positive (+ve); x is positive (+ve) to the right (→) and y is positive (+ve) upward (↑).

8.6.2 Settlement of a Pile Group

Exam Focus: [2012-Spring (PU): 6.(a)], [2013-Spring (PU): 7.(c)]
  • Because of the rigidity of the pile cap, all piles within a group settle almost equally. However, the total settlement of a pile group is significantly greater than that of a single pile carrying the same per-pile load, primarily due to the overlapping of stressed influence zones beneath closely spaced piles.
  • Group settlement is computed using the Equivalent Raft Method, in which the entire pile group is replaced by an equivalent flexible raft placed at an effective depth of (2/3) Df from the ground surface for friction piles in clay (as shown in Figure 1).
  • Assuming a 1H : 4V load dispersion from the top of the piles down to the equivalent raft plane, the effective width of the equivalent raft in clay becomes:
    Beq = B + 2 × (1/4) × (2Df / 3)
Consolidation Settlement Formulas:

1.   ΔH = Cc1 + e0 × H × log10 (σ0 + Δσσ0)  (for normally consolidated clays)

2.   ΔH = (Δe1 + e0) H     |     3.   ΔH = mv · Δσ · H
  • When a pile group passes through soft clay and rests on or near a firm sand stratum, the equivalent raft is located at a depth of (2/3) Df within the bearing stratum (or at the pile tips) with a 1H : 2V load spread below the equivalent raft (Figure 2).
1:4 1:4 1:2 1:2 2 3 Df Equivalent Raft Plane
Figure (1): Equivalent raft location and load dispersion for friction piles in uniform clay.
Clay Sand 1:2 1:2 Df 2 3 Df
Figure (2): Equivalent raft for piles penetrating clay into an underlying sand stratum.

8.7 Efficiency of a Pile Group

Exam Focus: [2013-Spring (PU): 4.(a)], [2014-Spring (PU): 6.(c)], [2015-Spring (PU): 6.(a)], [2016-Fall (PU): 7.(c)]
  • Definition: The group efficiency (ηg) of a pile group is defined as the ratio of the ultimate load-carrying capacity of the entire pile group to the sum of the ultimate capacities of the individual piles acting separately.
∴   ηg = Qu(g)n · Qu(s) × 100%
Where:
• ηg = Pile group efficiency (%)
• Qu(g) = Ultimate bearing capacity of the pile group
• Qu(s) = Ultimate bearing capacity of a single isolated pile
• n = Number of piles in the group
  • Governing Factors: Group efficiency depends on soil type (cohesive vs. cohesionless), method of installation (driven vs. bored), center-to-center pile spacing, load per pile, and total number of piles in the group.

8.8 Negative Skin Friction (Downward Drag)

When a pile passes through a compressible soft soil layer or freshly placed fill that settles downward relative to the pile shaft, the surrounding soil exerts a downward drag force known as negative skin friction (NSF), which reduces the net allowable capacity of the pile.

Negative skin friction Single pile Loose soil fill Lc Clay fill Sand Negative skin friction Group pile
Figure: Development of negative skin friction on a single pile and on a pile group passing through settling fill.

8.8.1 Calculation of Negative Skin Friction for a Pile Group

a) For Cohesionless Soil (Sand):

∴   QNSF(g) = n × QNSF(s)

b) For Cohesive Soil (Clay): Compute both individual and block drag forces and adopt the higher value for design:

i)   QNSF(g) = c · As(g) + γ · Lc · Ab(g)

ii)   QNSF(g) = n × QNSF(s)

Where Lc = thickness of the settling loose or soft soil layer undergoing negative skin friction, and γ = unit weight of the soil within depth Lc.

8.8.2 Remedial Measures to Reduce Negative Skin Friction

  1. Use piles of slender cross-section to minimize the surface area exposed to downward drag.
  2. Provide an annular space between the pile and driving casing filled with a viscous material (such as bentonite slurry) before withdrawing the casing.
  3. Coat the exterior surface of precast piles with bitumen prior to driving to reduce shaft adhesion in the settling zone.

8.9 Construction of Piles

i) Driven and Cast-in-Place Piles (Franki / Bulb Pile Method)

  • a) Forming the Plug: A steel casing is driven to a shallow initial depth, cleaned out, and a batch of dry concrete is placed at the bottom and rammed with a drop hammer to form a watertight plug.
  • b) Driving the Tube: Repeated blows of the internal falling ram onto the concrete plug pull the steel casing down to the required bearing depth.
  • c) Forming the Enlarged Base: Once at depth, the casing is held stationary while the concrete plug is expelled outward and heavily rammed with additional concrete charges to form an enlarged bulb base.
  • d) Forming the Shaft: The casing is gradually withdrawn while successive charges of concrete are rammed in place, creating a rough, high-friction concrete shaft.
(a) (b) (c) (d)
Figure: Sequence of operations for driven and cast-in-place bulb piles: (a) Plugging, (b) Driving, (c) Base forming, (d) Shaft concreting.

ii) Bored and Cast-in-Situ Under-Reamed Piles

  • a) Boring the Hole: A vertical borehole is excavated to the design depth using a hand-operated or mechanical spiral auger guided by a boring frame.
  • b) Forming the Under-Reamed Bulb: An under-reamer tool is lowered to the bottom of the cleaned borehole, pressed downward, and rotated so its expanding blades cut and collect soil into a bucket until an enlarged bulb cavity is formed.
  • c) Placing Reinforcement: A prefabricated steel reinforcement cage is lowered into position inside the borehole.
  • d) Concreting the Pile: Concrete is poured through a concreting funnel to complete the under-reamed pile shaft and bulb.
Boring guide Auger Under- reamer Rein- forcement Concreting funnel
Figure: Construction stages of a single under-reamed bored cast-in-situ pile.
COMPLETE BOARD EXAMINATION SOLVED NUMERICALS & QUESTIONS (Q1 TO Q25)
Q1–Q10. Theoretical Examination Questions & Detailed Reference Index
  • 1. Explain the procedure to obtain the settlement of a pile group. [2012-Spring (PU): 6.(a)], [2013-Spring (PU): 7.(c)] → Refer to Section 8.6.2 (Equivalent Raft Method located at 2/3 Df with 1:4 load dispersion in clay and Terzaghi's consolidation settlement analysis).
  • 2. Write a comprehensive short note on negative skin friction. [2012-S, 2013-S, 2014-S/F, 2016-S, 2020-F (PU)] → Refer to Section 8.8, 8.8.1, and 8.8.2.
  • 3. Describe the various types of pile foundations. → Refer to Section 8.1.2 (Complete classification by material, function, installation method, use, and soil displacement).
  • 4. Explain the efficiency of a pile group. [2013-Spring, 2014-Spring, 2016-Fall (PU)] → Refer to Section 8.7.
  • 5. Describe the pile load test and explain negative skin friction on piles. [2015-Fall (PU): 5.(b)] → Refer to Section 8.5 (Pile Load Test setup & IS 2911 criteria) and Section 8.8 (Negative Skin Friction).
  • 6. Does negative skin friction develop in pile foundations? Justify your answer and describe pile group efficiency. [2015-Spring (PU): 6.(a)] → Yes; downward drag develops whenever surrounding soft clay or fresh fill consolidates relative to the pile shaft. Refer to Sections 8.8 and 8.7.
  • 7. How can you estimate the load-carrying capacity of piles using pile-driving formulas? [2016-Spring (PU): 4.(a)] → Refer to Section 8.3.2 (ENR Formula and Hiley’s Formula).
  • 8. How can you estimate the load-carrying capacity of piles using static formulas and pile-driving formulas? [2017-Fall (PU): 4.(a)] → Refer to Sections 8.3.1 and 8.3.2.
  • 9. How do you calculate negative skin friction for a single pile and for a pile group in clay? [2017-Spring (PU): 4.(a)] → For a single pile: Qnsf(s) = α·cu·(π·d·Lc). For a group in clay, take the greater of n·Qnsf(s) and (c·As(g) + γ·Lc·Ab(g)) per Section 8.8.1.
  • 10. What reasons lead to the development of negative skin friction in a pile foundation, and how is it calculated for a pile group? [2018-Fall (PU): 5.(a)] → Caused by consolidation of freshly placed fill, lowering of the water table, or reconsolidation of remolded sensitive clay. Calculated per Section 8.8.1.
11. Describe briefly how the load-carrying capacity of a pile can be computed using various methods. Which method is the most reliable, and why?
[2018-Spring (PU): 6.(a)]
Detailed Solution

The ultimate load-carrying capacity of a single pile is evaluated using four principal approaches:

  • 1. Static (Analytical) Method: Applicable to both sand and clay strata (more reliable in cohesionless sands). The ultimate capacity is calculated as the sum of end-bearing resistance and skin-friction resistance:
    Qp = Qeb + Qsf = (Ab × qb) + (As × fs)
  • 2. Dynamic Formulas: Suitable for cohesionless sands; based on empirical energy-transfer relationships during driving (hence less accurate). Common formulas include the Engineering News-Record (ENR) Formula and Hiley’s Formula.
  • 3. In-Situ Penetration Methods: Relies on empirical correlations derived from field tests such as the Standard Penetration Test (SPT) and Cone Penetration Test (CPT).
  • 4. Pile Load Test (Most Reliable Method): Direct field load testing is the most accurate and reliable method for determining actual load-settlement behavior in the field, especially in dense sands and stiff soils. However, care is required in soft clays (due to remolding and consolidation time) and loose saturated sands (potential liquefaction under dynamic cyclic loading).
12. Compute the safe load-carrying capacity of a pile group consisting of 9 piles placed in a square pattern. Each pile has a diameter of 320 mm and a length of 13.5 m, spaced at 700 mm c/c. Take qu = 70 kPa, γ = 15 kN/m3, α = 0.7, and FOS = 2.5.
[2012-Spring (PU): 4.(b)]
Step-by-Step Solution
Given Data:
• Number of piles (n) = 9 (3 × 3 square pattern)
• Pile diameter (d) = 320 mm = 0.32 m
• Pile length (Df) = 13.5 m
• Center-to-center spacing (s) = 700 mm = 0.7 m
• Unconfined compressive strength (qu) = 70 kPa = 70 kN/m2
• Unit weight (γ) = 15 kN/m3,   α = 0.7,   FOS = 2.5,   Nc = 9
∴ Undrained cohesion, Cu = qu2 = 702 = 35 kN/m2
∴ Group plan dimensions: L = B = 2s + d = 2(0.7) + 0.32 = 1.72 m
G.L. Df L = (2s + d) B = (2s + d)

i) Individual Pile Failure Criterion:

Ab = πd24 = π × (0.32)24 = 0.0804 m2
As = π · d · L = π × 0.32 × 13.5 = 13.57 m2
Qu(s) = Cu Nc Ab + α Cu As = (35 × 9 × 0.0804) + (0.7 × 35 × 13.57) = 355.95 kN
∴   Qu(g) = n × Qu(s) = 9 × 355.95 = 3203.55 kN

ii) Block Failure Criterion:

Ab(g) = L × B = 1.72 × 1.72 = 2.96 m2
As(g) = 2(L + B) × Df = 2(1.72 + 1.72) × 13.5 = 92.88 m2
∴   Qu(g) = Cu Nc Ab(g) + α Cu As(g) = (35 × 9 × 2.96) + (0.7 × 35 × 92.88) = 3207.96 kN
Governing Ultimate Capacity Qu(g)min = 3203.55 kN  ⇒  Safe Load Qa(g) = 3203.55 / 2.5 = 1281.42 kN
13. A pile group consists of 9 piles of 30 cm diameter and 10 m length arranged in a square pattern in clay. If cohesion at the ground surface is 110 kN/m2 and at the base is 160 kN/m2, find the safe load-carrying capacity of the pile group. Take α = 0.6, s = 0.7 m c/c, and FOS = 3.
[2013-Spring (PU): 5.(a)]
Step-by-Step Solution
Given Data:
• n = 9,   d = 0.3 m,   Df = 10 m,   s = 0.7 m c/c
• Csurface = 110 kN/m2,   Cbase = 160 kN/m2
• α = 0.6,   FOS = 3
∴ Average cohesion, Cu = 110 + 1602 = 135 kN/m2
∴ L = B = 2s + d = 2(0.7) + 0.3 = 1.7 m
110 160 Cu = 135 kN/m2 Cohesion Profile

i) Individual Pile Failure Criterion:

Ab = π(0.3)24 = 0.0706 m2,    As = π(0.3)(10) = 9.424 m2
Qu(s) = Cbase Nc Ab + α Cu As = (160 × 9 × 0.0706) + (0.6 × 135 × 9.424) = 865.00 kN
Qu(g) = 9 × 865.00 = 7785 kN  ⇒  Qa(g) = 77853 = 2595 kN

ii) Block Failure Criterion:

Ab(g) = 1.7 × 1.7 = 2.89 m2,    As(g) = 2(1.7 + 1.7) × 10 = 68 m2
Qu(g) = (160 × 9 × 2.89) + (0.6 × 135 × 68) = 9669.6 kN  ⇒  Qa(g) = 9669.63 = 3223.2 kN
Safe Load-Carrying Capacity (Least of the two criteria) = 2595 kN
14. A group of 16 piles, 13 m long and 300 mm in diameter, is to be arranged in a square form in a clay soil with an average unconfined compressive strength of 60 kN/m2. Work out the center-to-center spacing of the piles for a group efficiency factor of 1.0.
[2014-Fall (PU): 4.(b)]
Step-by-Step Solution
Given Data:
• Number of piles (n) = 16 (4 × 4 square pattern)
• Pile length (Df) = 13 m,   Diameter (d) = 0.3 m
• Unconfined compressive strength (qu) = 60 kN/m2
• Take α = 1.0 for soft cohesive clay,   Nc = 9,   ηg = 1.0
∴ Undrained cohesion, Cu = 602 = 30 kN/m2
∴ Plan dimensions of 4 × 4 group: L = B = 3s + d = 3s + 0.3
Df = 13 m L = (3s + d) B = 3s + d

i) Individual Pile Failure Criterion:

Ab = π(0.3)24 = 0.0706 m2,    As = π(0.3)(13) = 12.25 m2
Qu(s) = Cu Nc Ab + α Cu As = (30 × 9 × 0.0706) + (1.0 × 30 × 12.25) = 386.562 kN
∴   Qu(g) = 16 × 386.562 = 6184.992 kN

ii) Block Failure Criterion & Spacing Optimization:

Qu(g) = Cu Nc Ab(g) + α Cu As(g) = 30 × 9 × (3s + 0.3)2 + 1.0 × 30 × [4(3s + 0.3) × 13]
      = 270(9s2 + 1.8s + 0.09) + 1560(3s + 0.3) = 2430s2 + 5166s + 492.3
For ηg = 1.0, equate Block Capacity = Individual Group Capacity:
2430s2 + 5166s + 492.3 = 6184.992  ⇒  2430s2 + 5166s − 5692.692 = 0
Solving the quadratic equation gives center-to-center spacing s = 0.80 m (80 cm)
15. A concrete pile 400 mm in diameter is driven into a deep deposit of sand. SPT N-value at the pile tip is 35. Estimate the ultimate load-carrying capacity of the pile.
Step-by-Step Solution
• Base area Ab = π(0.4)24 = 0.1257 m2
• Using empirical SPT correlation for end-bearing in sand: qb ≈ 40 N (in kN/m2) per cm of penetration or Meyerhof's correlation qb = 40 N · (Df/d) ≤ 400 N
• For N = 35, ultimate unit end bearing qb = 40 × 35 = 1400 kN/m2
• Qb = qb × Ab = 1400 × 0.1257 = 176.0 kN
Estimated Ultimate End-Bearing Capacity Qb = 176.0 kN
16. A timber pile of 350 mm diameter and 10 m length is driven into medium dense sand. Compute the skin friction resistance given average effective overburden pressure along the shaft = 65 kPa, K = 1.2, and δ = 30°.
Step-by-Step Solution
• Shaft area As = π · d · L = π × 0.35 × 10 = 10.99 m2
• Unit skin friction fs = K · σ'v · tan δ = 1.2 × 65 × tan(30°) = 78 × 0.5774 = 45.03 kN/m2
• Total Skin Friction Resistance Qs = fs × As = 45.03 × 10.99 = 494.88 kN
Total Skin Friction Resistance Qs = 494.88 kN
17. Design and verify a 4 × 4 square group of friction piles (16 piles, d = 0.6 m, Df = 15 m, s = 1.8 m c/c) in soft clay (Cu = 37.5 kN/m2, α = 0.8, FOS = 3) to safely support a structural load of 3500 kN.
Step-by-Step Solution
i) Individual Pile Failure Check: Single pile capacity Qu(s) = 282.74 kN  ⇒  Qu(g) = 16 × 282.74 = 4523.84 kN > 3500 kN
ii) Block Failure Check (neglecting end bearing): L = B = 3s + d = 3(1.8) + 0.6 = 6.0 m
    Qu(g) = α Cu As(g) = 0.8 × 37.5 × [2(6 + 6) × 15] = 10,800 kN
    Qa(g) = 10,8003 = 3600 kN > 3500 kN (OK)
Final Design: 16 piles (4 × 4 square pattern), Diameter d = 0.6 m, Length Df = 15 m, Spacing s = 1.8 m c/c (Individual failure governs).
18. Find the ultimate load-carrying capacity of a 50 cm diameter pile of length 10 m. The water table is at ground level (G.L.). The top 4 m is sand with γsat = 20 kN/m3 and ϕ = 32°. Take δ = 0.75ϕ and K = 1. The lower 6 m is clay with c = 30 kPa, ϕ = 0°, and α = 0.8.
[2016-Fall (PU): 6.(b)]
Step-by-Step Solution
Given Data:
• d = 0.5 m,   Df = 10 m (4 m sand + 6 m clay)
• K = 1,   ϕ = 32°,   δ = 0.75 × 32° = 24°
• γsat = 20 kN/m3  ⇒  γ' = 20 − 10 = 10 kN/m3
• Cu = 30 kN/m2,   α = 0.8,   Nc = 9
G.L. Df = 10 m 4 m 6 m Qs1 Qs2 Qb ← d = 0.5 m Sand (γsat=20) ϕ = 32° Clay C = 30 kN/m2 ϕ = 0°
1. Skin friction in sand layer (4 m): Qs1 = K · σv · tan δ · As1 = 1 × (20 − 10) × 4 × tan(24°) × (π × 0.5 × 4) = 111.89 kN
2. Skin friction in clay layer (6 m): Qs2 = α · Cu · As2 = 0.8 × 30 × (π × 0.5 × 6) = 226.19 kN
3. End-bearing resistance in clay: Qb = Cu · Nc · Ab = 30 × 9 × π(0.5)24 = 53.01 kN
Total Ultimate Load-Carrying Capacity Qu = 111.89 + 226.19 + 53.01 = 391.09 kN
19. A group of 9 piles, each 8 m long and 30 cm in diameter with a center-to-center spacing of 90 cm, supports a column in clay having qu = 180 kN/m2. Estimate the safe load for FOS = 3.0 and α = 0.6.
[2017-Fall (PU): 6.(b)]
Step-by-Step Solution
• n = 9 (3 × 3),   Df = 8 m,   d = 0.3 m,   s = 0.9 m c/c,   α = 0.6,   FOS = 3.0
• Cu = 180 / 2 = 90 kN/m2,    Group width: L = B = 2(0.9) + 0.3 = 2.1 m
i) Individual Failure: Qu(s) = 90 × 9 × π(0.3)24 + 0.6 × 90 × (π × 0.3 × 8) = 464.4 kN
    Qu(g) = 9 × 464.4 = 4179.6 kN  ⇒  Qa(g) = 4179.6 / 3 = 1393.2 kN
ii) Block Failure: Qu(g) = 90 × 9 × (2.1 × 2.1) + 0.6 × 90 × [2(2.1 + 2.1) × 8] = 7200.9 kN  ⇒  Qa(g) = 7200.9 / 3 = 2400.3 kN
Safe Group Load Qa(g) = 1393.2 kN (Minimum of individual and block criteria)
20. A group of 9 piles, 12 m long and 250 mm in diameter, is arranged in a square pattern in clay with qu = 60 kN/m2. Determine the center-to-center pile spacing required for a group efficiency factor of 1.0 (neglect tip bearing; take α = 0.9).
[2017-Spring (PU): 6.(b)]
Step-by-Step Solution
• n = 9,   Df = 12 m,   d = 0.25 m,   Cu = 60 / 2 = 30 kN/m2,   α = 0.9,   ηg = 1.0
i) Individual Failure (neglecting tip bearing): Qu(s) = 0.9 × 30 × (π × 0.25 × 12) = 254.47 kN  ⇒  Qu(g) = 9 × 254.47 = 2290.23 kN
ii) Block Failure: L = B = 2s + 0.25  ⇒  Qu(g) = 0.9 × 30 × 2(2s + 0.25 + 2s + 0.25) × 12 = 2592s + 324
Setting ηg = 1.0:   2592s + 3242290.23 = 1  ⇒  2592s = 1966.23  ⇒  s = 0.76 m
Required Center-to-Center Pile Spacing (s) = 0.76 m (76 cm)
21. A group of 16 piles of 50 cm diameter is arranged at a c/c spacing of 1.0 m in soft clay (Cu = 30 kN/m2, length = 9 m, α = 0.6). Neglecting end bearing, determine the ultimate load capacity and efficiency of the pile group.
[2018-Fall (PU): 5.(b)]
Step-by-Step Solution
• Group dimensions (4 × 4): L = B = 3s + d = 3(1.0) + 0.5 = 3.5 m
• Individual Failure: Qu(s) = 0.6 × 30 × (π × 0.5 × 9) = 254.46 kN  ⇒  Qu(g) = 16 × 254.46 = 4071.36 kN
• Block Failure: Qu(g) = 0.6 × 30 × [2 × (3.5 + 3.5) × 9] = 2268 kN
• Group Efficiency: ηg = 22684071.36 × 100% = 55.70%
Ultimate Load Capacity Qu(g) = 2268 kN  |  Group Efficiency ηg = 55.70%
22. A group of 36 square friction piles (300 mm × 300 mm) is arranged in a uniform 6 × 6 grid in soft clay with α = 0.7. Determine the optimum center-to-center spacing of the piles.
Step-by-Step Solution

Assume Cu = 30 kN/m2 (cancels out during optimization) and pile length = Df:

i) Individual Failure: Qu(s) = 0.7 × 30 × (4 × 0.3 × Df) = 25.2 Df
    Qu(g) = 36 × 25.2 Df = 907.2 Df   ...(i)
ii) Block Failure: L = B = 5s + 0.3
    Qu(g) = 0.7 × 30 × 2(10s + 0.6) Df = (420s + 25.2) Df   ...(ii)
Equating (i) and (ii): 907.2 Df = (420s + 25.2) Df  ⇒  420s = 882
L = (5s + 0.3) B = (5s + 0.3) Df
Optimum Center-to-Center Pile Spacing (s) = 882 / 420 = 2.1 m
23(a). A reinforced concrete pile weighing 30 kN (including helmet and dolly) is driven by a drop hammer weighing 40 kN with an effective fall of 80 cm. Average settlement per blow is 1.4 cm, total temporary elastic compression is 1.8 cm, e = 0.25, and FOS = 2. Determine the ultimate bearing capacity and allowable load using Hiley’s formula.
[2019-Fall (PU): 5.(a)]
Step-by-Step Solution
• Since W > e·P (40 kN > 0.25 × 30 = 7.5 kN), impact efficiency ηb = W + e2PW + P = 40 + (0.25)2(30)40 + 30 = 0.598
• Taking drop hammer efficiency ηh = 0.8:
Qu = W · h · ηb · ηh s + c2 = 40 × 80 × 0.598 × 0.8 1.4 + 1.82 = 665.6 kN
Ultimate Bearing Capacity Qu = 665.6 kN  |  Allowable Load Qa = 665.6 / 2 = 332.8 kN
23(b). A square group of 9 piles passes through a recently constructed cohesive fill of depth L = 3 m. Pile diameter is 30 cm and spacing is 90 cm c/c. Given qu = 60 kN/m2 and γ = 19 kN/m3, compute the negative skin friction load on the pile group.
[2019-Fall (PU): 5.(b)]
Step-by-Step Solution
• Cu = 60 / 2 = 30 kN/m2,   L = B = 2(0.9) + 0.3 = 2.1 m,   α = 0.6
i) Individual Pile Drag: Qnsf(s) = 0.6 × 30 × (π × 0.3 × 3) = 50.89 kN  ⇒  Qnsf(g) = 9 × 50.89 = 458.01 kN
ii) Block Perimeter Drag: Qnsf(g) = Cu As(g) + γ Lc Ab(g) = 30 × (4 × 2.1 × 3) + 19 × 3 × (2.1 × 2.1) = 1007.37 kN
Design Negative Skin Friction Load (Higher of the two) = 1007.37 kN
24. A group of 9 piles arranged in a square pattern was driven into soft clay extending from ground level to a great depth. Diameter = 30 cm, length = 10 m, qu = 70 kPa, and spacing = 90 cm c/c. Compute the allowable load on the pile group based on shear failure criteria for FOS = 2.5 (take α = 0.6).
[2020-Fall (PU): 5.(b)]
Step-by-Step Solution
• n = 9 (3 × 3),   d = 0.3 m,   L = Df = 10 m,   s = 0.9 m c/c,   FOS = 2.5,   α = 0.6
• Cu = qu / 2 = 70 / 2 = 35 kN/m2,    L = B = 2(0.9) + 0.3 = 2.1 m
i) Individual Failure Criterion: Qu(s) = (35 × 9 × π(0.3)24) + (0.6 × 35 × π × 0.3 × 10) = 22.27 + 197.92 = 220.19 kN
    Qu(g) = 9 × 220.19 = 1981.71 kN  ⇒  Qa(g) = 1981.71 / 2.5 = 792.68 kN
ii) Block Failure Criterion: Qu(g) = (35 × 9 × 2.1 × 2.1) + (0.6 × 35 × 2(2.1 + 2.1) × 10) = 1389.15 + 1764.0 = 3153.15 kN
    Qa(g) = 3153.15 / 2.5 = 1261.26 kN
Allowable Load on Pile Group (Minimum of individual and block criteria) = 792.68 kN
25. A precast concrete pile of size 40 cm × 40 cm is driven into stiff clay (Cu = 80 kN/m2). Determine the length of pile required to carry a safe load of 300 kN with FOS = 2.5. Take adhesion factor α = 0.50.
[2020-Fall (PU): 6.(b)]
Step-by-Step Solution
• Square pile section = 0.40 m × 0.40 m,   Cu = 80 kN/m2,   Qa = 300 kN,   α = 0.50,   FOS = 2.5,   Nc = 9
• Required Ultimate Load Capacity: Qu = Qa × FOS = 300 × 2.5 = 750 kN
• End-Bearing Resistance: Qb = Ab · Cu · Nc = (0.40 × 0.40) × 80 × 9 = 115.2 kN
• Skin-Friction Resistance: Qs = α · Cu · As = 0.50 × 80 × (4 × 0.40 × L) = 64 L
• Equating Total Capacity: Qb + Qs = Qu  ⇒  115.2 + 64 L = 750  ⇒  64 L = 634.8
Required Pile Length (L = Df) = 634.8 / 64 = 9.92 m (adopt 10.0 m)

Post a Comment

0Comments
Post a Comment (0)